OnPoint Pro Doors Grand Junction works the whole valley, from the ranch houses on the mesas and the older streets off North Avenue to Fruita, Clifton, Palisade, Loma, Whitewater and Mack. The estimate is free, and you can say no.
Tell us what the door is doing. Estimates are free, and the figure is in your hands before any work begins.
Six repairs cover nearly everything that goes wrong with a home garage door, and each has a page of its own. Out past the house we also do gate repair and gate opener repair.
The air here is dry enough that the grease on springs, rollers and hinges hardens into a crust. A dry spring rubs on itself with every turn of the shaft, and you can often hear it squeal and chatter long before it breaks.
The daily swing adds to it. A hot afternoon followed by a cold night flexes the steel and the weatherstrip through most of the year, which is part of why springs on the Western Slope seem to wear on a faster clock.
Rollers suffer too. Many builder doors came with thin stamped rollers or hard plastic wheels, and heat followed by cold cracks them. A cracked roller wobbles, the door shakes, and the drag lands on the cables and the opener.
A squealing spring or a shaking door isn't always close to failing, but it's worth a look before it picks a cold morning.
Every job runs the same way, so here it is in advance.
Expect a two-hour window and a call when the technician leaves the previous job. Delays come from us, early, not as a surprise.
The estimate is free. You get a look at the door, an explanation and the estimate, and a no is simply a no.
Say yes and the job is exactly what was agreed. Anything new found once the door is open is shown to you and agreed separately.
Before we leave: several cycles, a hand balance check, and a reverse test with something in the door's path. Parts and labor are guaranteed.
Three typical jobs, told as examples rather than records, with no names or addresses. If yours sounds like one of them, call the number above.
A ranch-house door had gone from quiet to grinding over one summer, and the opener had started to stall.
Cracked plastic rollers were swapped for sealed nylon on steel stems, the hinges and springs lubricated, and the opener's force reset.
Friday, late afternoon · no return trip
A roll-up door on an orchard shop had jumped its track after a roller let go.
The track was straightened, the door rehung, and the worn rollers replaced as a set.
A weekday morning · single visit
An old single-skin door on a large home had warped enough that it no longer closed evenly.
An insulated double door went in, measured and balanced, with new springs and seal and the opener set to the new weight.
Measured one week · installed the next
We serve this area · The valley is a long drive end to end, and the truck covers all of it, up the river to Palisade and down past Mack. If your town is on the map, call.
Torsion hardware works the same whoever made the door. The name matters for parts supply and a few proprietary designs, and that's about it.
| Name | What to know |
|---|---|
| Genie | Screw and belt drives. The Intellicode remote and the carriage are the usual weak points, and each is a part, not a new opener. |
| Overhead Door / Raynor | Ordinary hardware on the residential doors. |
| Clopay | Installed everywhere, and supported for parts long after the install. |
| Chamberlain myQ | The app and Wi-Fi side fail more than the motor. Usually a re-pair. |
| Sommer / Marantec | Unusual in the valley, so the model is confirmed before we set off. |
| LiftMaster / Chamberlain | Two badges, one maker. Nearly anything that fails is a stocked part. |
Not listed? Nearly every home door uses standard hardware, and the model number settles it in seconds.
The valley is a long drive from one end to the other, and no parts counter is open at seven in the evening. So the truck carries what breaks here, not a national list.
That means common-size springs, lift cables, drums, bearings, sealed rollers, hinges, brackets, opener gear kits, remotes, sensors and bottom seal. Panels and whole doors are ordered, and you hear that at the visit.
On the call, tell us whether the springs sit above the door or along the sides, one door or two, and where in the valley you are.
Our trucks spend their days in the Redlands, Orchard Mesa, Pear Park, Fruitvale and along North Avenue, not in a territory drawn up somewhere else.
Horizon Drive's shops and service doors are on the route as well, along with the orchards and vineyards toward Palisade.
Nothing is agreed until you've seen the free estimate. Decide against it and that's the end of it.
It's running dry and wearing faster than it should. A squealing spring isn't always close to breaking, but it's worth a look before it chooses a cold morning.
Thin stamped rollers and hard plastic wheels crack with the swing from hot days to cold nights. Sealed nylon rollers on steel stems hold up far better.
Yes, from Mack and Loma to Clifton, Palisade and Whitewater, and the truck carries the common spring sizes so most calls finish in one trip.
Yes. Evenings, nights and weekends are all working hours, and a door stuck open goes to the top of the list.
Yes, and you're free to say no. We'd rather hear no today than sell a repair the door didn't need.
Parts and labor both. If the fault comes back, so do we.
Yes. Service doors along Horizon Drive and shop doors out among the orchards are part of the work.
Rarely. Gears, boards, sensors and springs are shared across the market, and the common ones travel with the technician.
One call gets you a two-hour slot and a heads-up before the truck moves. Your details aren't sold, and nobody guesses at your door from a call center.
Free estimate across the Redlands, Orchard Mesa, Pear Park, Fruitvale, Fruita, Clifton, Palisade, Loma, Whitewater and Mack.
Most useful to know: the door's age, and whether the spring is a long coil above the door or a pair along the sides. We carry both, but knowing which shortens the visit.